Molded composite steering block of ‶medium※ hardness (M) for rubber-tire racing. The steering block features two Ackermann positions, and uses small but robust 5x10 ball-bearings to minimize unsprung weight. Can be also used for foam tires. Fits XRAY T2, T3 cars. 

Molded composite steering block of ‶hard※ hardness (H) for foam-tire racing. The steering block features two Ackermann positions, and uses small but robust 5x10 ball-bearings to minimize unsprung weight. Can be also used for rubber tires. Fits XRAY T2, T3 cars. 

Precision-machined bushing for front C-hub steering block pivot screws on XRAY T2, T3. Includes 4 pieces: 2 short + 2 long. 

Molded composite C-hub for front right steering block on XRAY T2, T3. Caster pre-set at 4° for neutral handling. Engraved with "4R" for easy identification. Use with left-side composite 4° C-hub #302346. 

Molded composite C-hub for front left steering block on XRAY T2, T3. Caster pre-set at 4° for neutral handling. Engraved with "4L" for easy identification. Use with left-side composite 4° C-hub #302345. 

Molded composite C-hub for right steering block of T2, T3. Caster pre-set at 4°. Medium rigidity for rubber-tire racing. Use with matching left-side C-hub #302364. Can be also used for foam tires. 

Molded composite C-hub for left steering block of T2, T3. Caster pre-set at 4°. Medium rigidity for rubber-tire racing. Use with matching right-side C-hub #302363. Can be also used for foam tires. 

Molded composite C-hub for right steering block of T2, T3. Caster pre-set at 4°. Hard rigidity for foam-tire racing. Use with matching left-side C-hub #302374. Can be also used for rubber tires. 

Molded composite C-hub for left steering block of T2, T3. Caster pre-set at 4°. Hard rigidity for foam-tire racing. Use with matching right-side C-hub #302373. Can be also used for rubber tires. 

Molded composite 4.9mm ball joints, open on both sides, for connection to 4.9mm ball. Set of eight. Fits XRAY T2, T3. 

Molded composite 4.9mm ball joints, special construction. For connection to 5mm ball. Set of four. Fits XRAY T2, T3. 

QRC (Quick Roll Center™) holders pre-assembled with #302664 unidirectional ball joints. 

Alu shims 3x6mm size, 1mm thick. Silver color, set of 10. 

Alu shims 3x6mm size, 2mm thick. Silver color, set of 10. 

Set of two adjustable turnbuckle for adjusting camber of rear uprights, manufactured from world-renowned top-secret "Hudy Spring Steel". 

Molded-composite rear upright features built-in 0° of outboard toe to improve traction and prevent suspension geometry changes in serious crashes. Medium rigidity (labeled ‶M※) specially optimized for rubber-tire racing. Use on both left and right sides of the car. Can be also used for foam tires. 

Molded-composite right rear upright features built-in 1° of outboard toe-in to improve the rotation of the car in corners and prevent suspension geometry changes in serious crashes. Hard rigidity (labeled ‶H※) specially optimized for foam-tire racing. Use with matching left-side rear upright 303363. Can be also used for rubber tires. 

Molded-composite left rear upright features built-in 1° of outboard toe-in to improve the rotation of the car in corners and prevent suspension geometry changes in serious crashes. Hard rigidity (labeled ‶H※) specially optimized for foam-tire racing. Use with matching right-side rear upright 303353. Can be also used for rubber tires. 

Hudy Spring Steel™ drive shaft coupling for Set Screw for increased reliability, works in front and rear CVD drive shafts of XRAY T2, T3. Specially hand-ground for maximum precision.  

Low friction 3.5mm drive pin clips for protection and cushioning of drive shaft pin in diff outdrives. Set of 4. For use only with T2'008 XRAY alu ball-diffs or Multi-Diff™. 

CNC-machined 50mm drive shaft for XRAY T2,T3 made from world-renowned top-secret HUDY Spring Steel™. This race-quality drive shaft is the smallest in the world, exclusively manufactured by HUDY.  

CNC-machined 52mm CVD drive shaft made from world-renowned top-secret HUDY Spring Steel™. This race-quality drive shaft is the smallest in the world, exclusively manufactured by HUDY. Drive shaft diff end has been strategically lightened to reduce rotating mass without compromising strength.  

XRAY proudly presents the new ECS drive shaft 50mm, designed with high-level racing in mind. The ECS drive shafts were developed to decrease front wheel vibration when racing with a solid front axle, thus providing a much smoother and quieter ride and increasing steering. 

Super-lightweight 52mm alu drive shaft CNC-machined from premium Swiss 7075 T6 and hardcoated for extra durability and stylish looks. New design is up to 40% lighter than steel drive shaft. 

XRAY proudly presents the new ECS drive shaft 52mm, designed with high-level racing in mind. The ECS drive shafts were developed to decrease front wheel vibration when racing with a solid front axle, thus providing a much smoother and quieter ride and increasing steering. 

Super-lightweight 50mm alu drive shaft CNC-machined from premium Swiss 7075 T6 and hardcoated for extra durability and stylish looks. New design is up to 40% lighter than steel drive shaft. 

CNC-machined drive axles for XRAY T2, T3 made from world-renowned top-secret HUDY Spring Steel™. 

Super-lightweight drive axle for XRAY T2, T3 CNC-machined from world-renowned, top-secret HUDY Spring Steel™. Reduces rotating weight by up to 35% over standard outdrive. 

CNC-machined clamping-style alu wheel hubs for XRAY T2, T3. Set of two. 

CNC-machined clamping-style alu wheel hub for T2, T3 features -0.75mm offset to give more narrow track-width. Set of 2. 

CNC-machined clamping-style alu wheel hub for T2, T3 features 0.75mm offset to give wider track-width. Black color. Set of 2. 

CNC-machined clamping-style alu wheel hub for T2, T3 features 1.5mm offset to give wider track-width. Set of 2 includes clamping screws. 

Strong, lightweight composite wheel hubs for 1/10 touring car. Set of 2. 

Front lower outer pivot pins for XRAY T2, T3. Hardened for very high durability and long life. Set of two. 

Rear lower outer pivot pins for XRAY T2, T3. Hardened for very high durability and long life. Set of two. 

Specially-machined 5.0mm pivot ball with double bevel shoulders, for use with open 5.0mm ball joints on XRAY T2, T3. Set of 10. 

M3x2.5 setscrew, hex drive. Set of 10. 

M3x4 setscrew, hex drive. Set of 10 pieces. 

Setscrews with hex drive. M3x25. Set of 10. 

M3x6 button-head machine screw, hex drive. Set of 10 pieces. 

M3x10 button-head machine screw, hex drive. Set of 10 pieces. 

M3x14 button-head machine screw, hex drive. Set of 10 pieces. 

New high-speed ball-bearings manufactured specially for XRAY. ID x OD x thickness (mm) = 5x10x4. Set of 2 pieces. 

Polished chrome pin. Dia. x length = 2mm x 9.8mm. Set of 10 pieces.